Bowers-group Baty - Digital Indicator - DI-1 Manuel d'utilisateur télécharger pdf

DIGITAL INDICATOR INSTRUCTIONS

For more information visit www.baty.co.uk precision measuring instruments

Features

1. ZERO/ON

2. Tolerance indication

3. ABS / Preset function

4. Min, Max, TIR function

5. Direct mm-in conversion

6. Digital bar graph display

7. Battery cover

Operation

ZERO/ON: To turn the indicator on press the ZERO/ON button momentarily. Holding the button

for longer than 2 seconds will turn the indicator off. The zero function may be used whether in

the comparative or absolute mode. A quick press of less than 2 seconds will set the digits of the

display to 0. If the indicator is not used for approximately 10 minutes, it will turn off

automatically.

UNIT: A quick press of this button will change the indication of the display to either mm or inch.

ABS: A quick press of this button will toggle between absolute and comparative modes;

In comparative mode, ZERO may be set anywhere within the travel of the spindle.

In ABS mode, a long press of more than 2 seconds will start the PRESET function and this will be indicated by the word SET appearing in the

display. Release the button. To preset the display, hold the ABS button for another 2 seconds. SET will flash twice and then the first digit in the

display will begin to flash. Quick presses of the ABS button will increment the digit as it flashes. To move to the next digit, hold the ABS button

until the desired position in the display is reached. When the correct preset is achieved, hold ABS until SET begins to flash and then release.

Press ABS quickly once more and the preset is then stored. If at any time during the preset function ZERO is pressed, the SET function will

terminate and must be restarted. The ABS preset will be retained even after the indicator has been switched off. In the ABS mode, any time

the ZERO/ON button is pressed, the preset number will appear.

RAN: A quick press of this button will switch between MAX, MIN and MIN/MAX (TIR). While in the MAX mode (>|) the highest reading will be

held. While in the MIN mode (|<) the lowest reading will be held. While in MIN/MAX mode (>||<) the difference between minimum and

maximum will be displayed. Pressing ZERO at any time during one of these modes resets the function.

TOL: A quick press of this button will toggle the measuring direction from positive to negative. To start the TOL mode, hold in the button for

more than 2 seconds. (>|) and SET will appear in the display. Holding the button longer will enter into the PRESET function so the upper

tolerance may be entered. The actual target reading must be entered, not the allowed tolerance. This can be preset using the TOL button,

exactly as in the ABS mode. Once the upper reading has been entered, hold in TOL until SET begins to flash and release the button. One short

press will show (|<) and SET in the display. Now the lower reading may be entered in the same manner as the upper reading. Once this has

been done, hold in TOL until SET begins to flash again and release. A quick press of the TOL button will begin the TOLERANCE mode. While

the reading of the indicator is between the set tolerance readings the display will show OK. If the reading exceeds either tolerance reading,

(|<) or (>|) will appear. To exit this mode, press either TOL or ZERO. NOTE: The indicator must be zeroed at the reference location before the

TOL mode begins.

Digital Indicator – DI-1

Please carefully review these instructions to ensure proper and accurate use of your new Digital Indicator.

Maintenance

• Avoid contact with liquids and excess humidity

• If the instrument requires cleaning, only use isopropyl Alcohol

and a soft cloth

• Do not electro-etch this product

Specifications

Measuring range: 0-12.7mm/0.5"

Resolution: 0.001mm/0.00005"

Accuracy: 0.008mm/0.0003"

Battery: 3V, type CR2032 lithium

Digital_Indicator_410_02DF_baty 16/07/2010 17:21 Page 1

Digital Indicator – DI-1 1

Résumé du contenu

Page 1 - Digital Indicator – DI-1

DIGITAL INDICATOR INSTRUCTIONSFor more information visit www.baty.co.uk precision measuring instruments Features1. ZERO/ON2. Tolerance indication3.

Commentaires sur ces manuels

Pas de commentaire

Bowers-group Baty - Digital Indicator - DI-1 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Instruments de mesure Bowers-group Baty - Digital Indicator - DI-1. Bowers Group Baty - Digital Indicator - DI-1 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de mesure Bowers-group Baty - Digital Indicator - DI-1